Southern Stars • Support • Sky. Safari Manual • Scope Communication. The Scope Communication settings specify what kind of telescopeyou have, and how Sky. Safari should communicatewith your telescope. Click to enlarge. Use these settings to specify what kind of telescope hardware you have, and how Sky. Safari should communicate with your telescope. In order to communicate with your telescope, you will need either: a Wi- Fi- to- serial adapter, like our Sky. Fi or Orion's Star. Seek Wi- Fi Module, that relays wireless communication from your i. Phone or i. Pod, to the serial port on your telescope. Sky. Wire serial cable accessory, which connects your i. Phone directly to the serial port on your telescope. If you don't have such an adapter, you can also use Carina's Voyager software, running on a Mac or PC with Wi- Fi and a serial port, as a Wi- Fi- to- serial server. See Southern Stars's web site at www. Equipment Selection. Scope Type: Use this setting to select the type of telescope to control. Sky. Safari can control any of the telescopes in the list. Many "Go- To" telescopes can emulate the Meade LX- 2. Your telescope may need to be set to "LX- 2. Sky. Safari supports many encoder systems that can read out the telescope position but not actually move the telescope. 3 More options 36 Using digital text 36 Using teletext 36 Adding channels that aren’t listed in Sky Guide 37 Watching your added channels 37 Changing the picture settings 38 Remote control setup 39 Resetting your remote control 39 Replacing the batteries. Installation and Operation Manual 4 battery voltage and output current display without setup or control capability. It uses the same display circuit board as the display in the Solar Boost 3024Di. The full featured IPN-ProRemote incorporates a multi-line backlit LCD. Scope Setup Use these settings to specify what kind of telescope hardware you have, and how SkySafari should communicate with your telescope. In order to communicate with your telescope, you will need either: a Wi-Fi-to-serial adapter, like our SkyFi or Orion's. Revision Date: March 24, 2007 1 - 1 Revision 5.0 1 GENERAL INFORMATION 1.1 INTRODUCTION This manual contains information relative to the physical, mechanical, and electrical installation of the Sky Connect “Aviation” Systems. Operating procedures are. From your Home screen, go to Settings, Status and make sure Connection to Sky Q box has a tick. Go to Settings, System info and highlight Software version. Choose Setup and then select Software download. Your box will start to download the latest software via. The Meade Magellan I and II, Losmandy DSC, and Sky Commander are examples of such encoder systems. Mount Type selection, with options for encoders. Click to enlarge. Mount Type: Use this setting to select your telescope's type of mounting. Equatorial Fork - a clock- driven equatorial platform with fork arms that suspend the telescope between them. The Meade LX- 2. 00 and Celestron Nex. Star (when used with an equatorial wedge) are examples. German Equatorial - a clock- driven, polar- aligned mount that requires reversing the telescope tube to the east or west side of the mount when the telescope passes through the meridian. Examples include the Losmandy and Takahashi mounts. Equatorial Platform - mountings that sit on motorized platforms, where the encoders move with the mount. Alt- Azimuth Fork - a non- motorized alt- azimuth platform that is moved manually by pushing the telescope tube. Includes most Dobsonian telescopes. Alt- Azimuth Go. To - a clock- driven alt- azimuth platform with fork arms that suspend the telescope between them, and can slew to any set of coordinates in the sky on command. Includes the Meade LX- 2. Celestron Nex. Star when used in the alt- azimuth configuration. If your telescope mount has encoders which provide a digital readout of the scope's position, additional text fields will appear here. These let you specify the encoder resolution. RA/Azm: The number of steps per revolution for the encoder attached to the telescope's Right Ascension axis (or Azimuth axis, if you have an alt- azimuth mount). Dec/Alt: The number of steps per revolution for the encoder attached to the telescope's Declination axis (or Altitude axis, if you have an alt- azimuth mount). Get Automatically: If turned on, Sky. Safari will attempt to read these values from your encoders when it connects to the telescope controller. If turned off, you can enter the encoder steps per revolution manually; then Sky. Safari will send the values you entered to the encoders when connecting to the telescope. You can do this if (for example) your mount is using gears or pulleys to increase the effective encoder resolution. Depending how your encoders are installed, their position readouts may increase when they are turned clockwise, or increase when they are turned counterclockwise. If the encoder position readouts increase when they are turned counterclockwise, enter a negative value for the number of steps per revolution. You may need to determine the correct + or - sign by trial- and- error. If you push your telescope left (or up), but the telescope field- of- view indicator on the sky char moves right (or down), the sign is probably wrong. Communication Settings. The first two settings below (IP address and TCP port) are only used with Wi- Fi telescope communication. If Sky. Wire is connected to your i. Phone, i. Pad, or i. Pad Touch, Sky. Safari will use Sky. Wire (rather than Wi- Fi) to communicate with your telescope. IP Address: The IP address of the Wi- Fi adapter or server that is physically connected to the telescope. Your i. Phone or i. Pod must be on the same Wi- Fi network as the adapter or server, and must have an IP address on the same subnet. Check your i. Phone's Wi- Fi network settings to make sure this is correct. Port Number: The TCP port number to be used for communication with the adapter. Make sure this is the same TCP port that the telescope adapter or server is listening on. Set Time and Location: If turned on, Sky. Safari will send the time and location from your i. Phone to the telescope when establishing a connection. This will overwrite your telescope's previously- set time and location. For older Meade LX- 2. Readout Rate: The readout rate is the frequency with which Sky. Safari requests the telescope's position from the mount so it can update the position on- screen. If you set this rate to "4 per second", then Sky. Safari will request the telescope's position four times every second. If the telescope frequently stops communicating, the rate of position requests may be too frequent for the telescope to respond properly. Setting a lower readout rate of 1 or 2 readouts per second may solve the communication problem. The optimal readout rate varies with the type of mount used and may require some trial and error to determine. A lower readout rate means that the telescope position displayed on the sky chart will be updated less frequently, and using Sky. Safari to control the telescope may feel sluggish. Sky. Fi Settings Web Page: If you have a Sky. Fi wireless adapter, this item displays its settings/configuration web page. You must be connected to Sky. Fi's wireless network in order to see this web page, and the Sky. Fi's IP address must match the IP address entered at the top of the view.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |